|
|
| TECHNICAL INFORMATION |
|
|
|
|
Close
|
| BEARING
TOLERANCE |
|
|
| Tolerances
of Housings |
|
|
|
|
| Spherical
Bore Diameter of Housings |
|
unit:¦Ìm/0.0001 inch |
|
|
| Nominal outside diameter
D |
Tolerance class H7 |
Tolerance class J7 |
|
|
|
|
| over |
Incl. |
¡÷Damp
Deviations |
¡÷Das
Deviations |
¡÷Damp
Deviations |
¡÷Das
Deviations |
|
|
| mm |
Inch |
mm |
Inch |
high |
low |
high |
low |
high |
low |
high |
low |
|
|
| 30 |
1.1811 |
50 |
1.9685 |
+25
+10 |
0
0 |
+30
+12 |
-5
-2 |
+14
+6 |
-11
-4 |
+19
+7 |
-16
-6 |
|
|
| 50 |
1.9685 |
80 |
3.1496 |
+30 +12 |
0
0 |
+36 +14 |
-6
-2 |
+18
+7 |
-12
-5 |
+24
+9 |
-18
-7 |
|
|
| 80 |
3.1496 |
120 |
4.7244 |
+35
+14 |
0
0 |
+42
+17 |
-7
-3 |
+22
+9 |
-13
-5 |
+29
+11 |
-20
-8 |
|
|
| 120 |
4.7244 |
180 |
7.0866 |
+40
+16 |
0
0 |
+48
+19 |
-8
-3 |
+25
+10 |
-14
-6 |
+34
+13 |
-22
-9 |
|
|
| 180 |
7.0866 |
250 |
9.8425 |
+46
+18 |
0
0 |
+55
+22 |
-9
-4 |
+30
+12 |
-16
-6 |
+39
+15 |
-25
-10 |
|
|
| 250 |
9.8425 |
315 |
12.4016 |
+52
+20 |
0
0 |
+62
+24 |
-10
-4 |
+36 +14 |
-16
-6 |
+46
+18 |
-26
-10 |
|
|
|
|
| Dimensional
tolerances for spherical bore diameter of housing are classified as H7 for
clearance fit, and J7 for internediate fit. |
|
|
|
|
|
| Pillow
Block Housings (PE, PA, TB, AK) |
|
unit:¦Ìm/0.0001 inch |
|
|
| KML
No. |
H Deviations
¡÷Hs
|
|
|
|
| PE203 |
- |
- |
- |
¡À150
¡À59 |
|
|
|
| PE204 |
PA204 |
TB204 |
AK204 |
|
|
|
| PE205 |
PA205 |
TB205 |
AK205 |
|
Pic( |
|
|
| ¡¡ |
|
|
|
|
| PE206 |
PA206 |
TB206 |
AK206 |
|
|
|
| PE207 |
PA207 |
TB207 |
AK207 |
|
|
|
| PE208 |
PA208 |
TB208 |
AK208 |
|
|
|
| ¡¡ |
|
|
|
|
| PE209 |
PA209 |
TB209 |
AK209 |
|
|
|
| PE210 |
PA210 |
TB210 |
AK210 |
|
|
|
| PE211 |
- |
- |
- |
¡À200
¡À79 |
|
|
|
| ¡¡ |
|
|
|
|
| PE212 |
- |
- |
- |
|
|
|
| PE213 |
- |
- |
- |
|
|
|
| PE214 |
- |
- |
- |
|
|
| ¡¡ |
|
|
|
| PE215 |
- |
- |
- |
|
|
|
|
| H
is height of the shaft center line. |
|
|
|
|