|
|
| TECHNICAL INFORMATION |
|
|
|
|
|
Close
|
| BEARING
TOLERANCE |
|
|
| Tolerances
of Housings |
|
|
|
|
|
|
| Flange
unit housings (F, FS, FC, FCS, FL, FT, FD, LF) |
|
unit:¦Ìm/0.0001 inch |
|
| KML
No. |
e
Deviations ¡÷es |
i
Deviations ¡÷is |
f
Deviations
¡÷fs
|
Radial runout of spigot
joint ¡÷is
max |
|
| FC - FCS |
|
| high |
low |
|
| F203 |
- |
- |
FL203 |
FD203 |
LF203 |
¡À700
¡À276 |
¡À500
¡À197 |
0
0 |
-46
-18 |
200
79 |
|
| F204 |
FC204 |
FCS204 |
FL204 |
FD204 |
LF204 |
|
| F205 |
FC205 |
FCS205 |
FL205 |
FD205 |
LF205 |
|
| ¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
|
| F206 |
FC206 |
FCS206 |
FL206 |
FD206 |
LF206 |
|
| F207 |
FC207 |
FCS207 |
FL207 |
FD207 |
LF207 |
¡À700
¡À276 |
¡À500
¡À197 |
0
0 |
-54
-21 |
200
79 |
|
| F208 |
FC208 |
FCS208 |
FL208 |
- |
- |
|
| ¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
|
| F209 |
FC209 |
FCS209 |
FL209 |
- |
- |
|
| F210 |
FC210 |
FCS210 |
FL210 |
- |
- |
|
| F211 |
FC211 |
FCS211 |
FL211 |
- |
- |
¡À1000
¡À394 |
¡À800
¡À315 |
0
0 |
-63
-25 |
300
118 |
|
| ¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
|
| F212 |
FC212 |
FCS212 |
FL212 |
- |
- |
|
| F213 |
FC213 |
FCS213 |
FL213 |
- |
- |
|
| F214 |
FC214 |
FCS214 |
FL214 |
- |
- |
|
| ¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
¡¡ |
|
| F215 |
FC215 |
FCS215 |
FL215 |
- |
- |
|
| F = FS |
|
|
| FL = FT |
|
|
| 1) e is the bolt hole's center line dimension. i is distance between the center line
of spherical bore diameter of the |
|
| housing and mounting
surfaces, and f is outside diameter of the spigot joint. |
|
|
| 2)
Radial runout of spigot joint is applied for flange units with spigot joints. |
|
|
| 3)
For FS and FT types, tolerances for F shall be applied. |
|
|
|
|